After I year of using I know the machine has a serious hygienic issue. Despite of cleaning the machine every month, as recommended, inside of the machine, on the infuser and inside of the chamber I experience a mould.
Also the front door is not removable, so you can’t properly clean it, as the door should be soaked in the water for a proper cleaning.
Unfortunately I have cleaned the mould from the infuser before I decided to do this review so I can’t show the problem in the pictures, but it was quite bad. My guess is the infuser should be perfectly dry before attaching back to the machine.
But I managed to upload the pictures of the front door and the spouts. Also the chamber inside is so complicated than it is almost impossible to clean it properly. Please trust me, the front door is impossible to clean properly if you can’t remove it from the machine.
This is why I decided to find the way how to remove the front door together with spouts from the machine. What had to be done was to drill a small hole at the bottom of the door and then I managed to remove the hinge pin with a small pliers. Do not try to use a standard size pliers as they are too big.
After cleaning, it is easy to put the hinge pin back, it sits quite tight, so I do not think it will keep moving out while the door opens and closes.
Good luck – please remember, you do it on your own responsibility 🙂
Jak pozbyć się z domu muszek owocówek – domowy sposób
Metoda ta srawdza się nie tylko w przypadku muszek owocówek, ale much w ogóle, a także komarów i innych insektów. Wystarczy mieć w domu cytrynę, limonkę i paczkę goździków.
Przekrój cytrynę na pół i do każdej części wbij ok. 10 goździków. Tak przygotowane owoce ustaw tam, gdzie muszki pojawiają się najczęściej – w kuchni, na parapecie okna, na stole w ogrodzie. Po krótkim czasie przekonasz się, że owady znikną szybko i bez śladu, nie pojawią się też nowe.
Dlaczego cytryny z goździkami odstraszają muszki? Wszystko dzięki ich zapachowi – intensywny aromat goździków i cytrusów skutecznie odstrasza insekty, a nam przynosi nie tylko ulgę, jest również fajnym naturalnym odświeżaczem powietrza i dekoracją.
Zamiast całych goździków i cytryn, można użyć również goździkowego olejku eterycznego (wystarczy dodać go do środków czyszczących).
Small explanation about using simplified rep. in Creo PTC with example.
Today I was doing 3D model and drawing of the aluminium frame. To do it correctly welders have to use welding jig. There is no point to keep it shown in the 3D model however if you simply hide it you won’t be able to show it in the drawings (using component display will not work).
The solution is simplified rep. Open view manager, click Simp Rep tab, click new and type (in my case) Welding.
The last part is set up as invisible in welding view, but will be visible in master rep view.
It is a bit sad part of my family’s history. During the WWII my mum’s step sister was a member of a resistance movement and was caught in 1941. She was sent to Ravensbruck Nazi camp where she was a part of medical experiments done by German doctors.
She was freed in 1945 by allies and sent to Sweden by the Swedish Red Cross for a treatment. Unfortunately she was in a very bad condition and after returning to Poland she died very soon. During her treatment in Sweden she got a small gift – a china rabbit – as she was an experimental rabbit. We have got the rabbit in our Welsh dresser.
My wife asked me to print a funnel. I realised that I have never before printed anything in vase mode. The first attempt gave me a nice funnel, however only the narrow bit of the funnel has been printed in vase mode. The wide part got an unwanted seam.
I have quickly realised the angle is a key factor. The wide part of the funnel had 45 deg. angle. I changed that to 50deg and… voila 🙂 The printer is printing perfect seamless funnel 🙂